Efficient PL Emission from p-type Porous Silicon: A Comparative Study for Selection of Effective Anodization Parameters

The physical mechanism of highly efficient photoluminescence (PL) emission from p-type silicon is described by a comparative study of the effectiveness of the etching parameters in an electrochemical anodization technique. Two series of porous silicon samples were prepared in a combination of anodization current and time, to maintain the total amount of anodic charge transfer constant. Photoluminescence studies show that irrespective of the amount of charge transfer, the samples prepared with comparatively higher current density show an efficient PL as well as stronger blueshift in the emission energy vis-à-vis the samples prepared for longer durations. An overall decrease in crystallite size, as estimated by Raman spectral analysis, was observed for both series of samples with the progress of charge transfer. Comparative analysis shows a marginal difference in crystallite size for both series of samples in the initial state of charge transfer, whereas major differences arise at higher values. This is explained with the formation of silicon suboxide on the porous surface at higher current density, leading to initiation of side wall reaction, and higher reduction rate in crystallite size as well as strong luminescence due to the carrier quantum confinement effect.     

Matrix Transformation in Boron Containing High-Temperature Co–Re–Cr Alloys

An addition of boron largely increases the ductility in polycrystalline high-temperature Co–Re alloys. Therefore, the effect of boron on the alloy structural characteristics is of high importance for the stability of the matrix at operational temperatures. Volume fractions of ε (hexagonal close-packed—hcp), γ (face-centered cubic—fcc) and σ (Cr₂Re₃ type) phases were measured at ambient and high temperatures (up to 1500 °C) for a boron-containing Co–17Re–23Cr alloy using neutron diffraction. The matrix phase undergoes an allotropic transformation from ε to γ structure at high temperatures, similar to pure cobalt and to the previously investigated, more complex Co–17Re–23Cr–1.2Ta–2.6C alloy. It was determined in this study that the transformation temperature depends on the boron content (0–1000 wt. ppm). Nevertheless, the transformation temperature did not change monotonically with the increase in the boron content but reached a minimum at approximately 200 ppm of boron. A probable reason is the interplay between the amount of boron in the matrix and the amount of σ phase, which binds hcp-stabilizing elements (Cr and Re). Moreover, borides were identified in alloys with high boron content.     

Imaging of two-dimensional unsaturated moisture flows in uncracked and cracked cement-based materials using electrical capacitance tomography

The development of visualizing tools to monitor unsaturated moisture flow in cement-based materials is of great importance, as most degradation processes in cement-based materials are connected to and take place in the presence moisture. This paper investigates the ability of electrical capacitance tomography (ECT) to image two-dimensional (2D) unsaturated moisture flow in cement-based materials. In ECT, the electrical permittivity distribution within an object is reconstructed based on measured capacitances between electrodes attached on the object’s surface. In a series of experiments, mortar specimens with and without discrete cracks were imaged with ECT during a 2D moisture ingress. The results show that ECT is able to monitor the evolution of the moisture flow, and to approximate the shape and position of the moisture front. These findings indicate that ECT is a viable method for monitoring and visualizing 2D unsaturated moisture flow in cement-based materials in the presence and absence of discrete cracks.     

Appraisal of Agriglass in Promoting Maize Production Under Abiotic Stress Conditions

An agriglass composition containing different oxides acts as a slow release for macro and micro nutrients and was chosen to improve maize yield under most important abiotic stresses which affecting agriculture development; salinity and drought. A field experiment was performed in salt affected soil (EC =?7.5 dSm^??1) by using different water deficit rates (I1 = 100, I2 = 85 and I3 = 70% of maize water requirements). Irrigation levels were located in main plots. Every main-plot divided into six sub-plots contained glassy fertilizer treatments [F1 = 55 kg fed^?1 with 1/2 mm diameter of agriglass (fed. =?4200 m²), F2 = 55 kg fed^?1 with 1 mm diameter, F3 = 80 kg fed^?1 with 1/2 mm diameter, F4 = 80 kg fed^?1 with 1 mm diameter, F5 = Recommendations of Ministry of Agriculture and F6 = control]. The experimental results demonstrated that, ears, straw, grains and biological yields increased with increasing both water and agriglass rates. Application of agriglass as a slow release fertilizer improved yield more than mineral fertilizer. Some growth parameters, water use efficiency (IWUE), macronutrients concentration and their relations were included. Other studies on residual effect of agriglass and the annual application rates to withstand salinity and drought stress by strategic crops are required.     

Effect of ZnO layer thickness upon optoelectrical properties of NiO/ ZnO heterojunction prepared at room temperature

In this work, p-NiO/n-ZnO heterostructures were successfully prepared at room temperature using RF sputtering technique. The influence of ZnO layer thickness on the performance of the heterojunction was investigated. The deposited ZnO layers have a hexagonal Wurtzite structure with preferable growth orientations along (002) and (103) for thinner films. Increasing the thickness results in more crystallographic orientation randomness. The current–voltage measurements of the realized heterojunctions showed a clear rectifying behavior. The measured ideality factor varies from 2.5 to 1.6 according to the thickness of ZnO layer. The series resistance of the device is enlarged with increasing ZnO thickness. The deduced parameters from the I–V characteristics suggest that 200 nm is the optimal thickness of the ZnO layer according to our experimental conditions. We attribute the relatively better performance of this thickness to achieving reasonable compensation between serial resistance and ideality factor. The best heterojunction was tested and successfully used as a UV detector.     

Cross-Layer Optimization of Dynamic Packet Assignment for Video Transmission Over IEEE 802.11e Networks

Video transmission over IEEE 802.11e wireless networks still shows poor performance for large bandwidth demand and frequently changed environments. Thus, several enhancements of IEEE 802.11e were proposed. On the other hand, big frames and simultaneous sending of adjacent frames always cause packet dropping for buffer overflow. In the past, we proposed an IEEE 802.11e enhancement named DFAA and a content aware mechanism to solve the above problems. The motivation of this paper is to find a proper way to integrate these two mechanisms. A DFAA enhancement (DFAA-E) is proposed to make up the insufficiency of content aware mechanism. Experiments results show that the combination of DFAA-E and content aware mechanism improves the video decoded quality greatly. And its performance can be further enhanced by selecting the suitable settings of certain parameters.     

Reoptimization framework and policy analysis for maritime inventory routing under uncertainty

We study a maritime inventory routing problem, in which shipments between production and consumption nodes are carried out by a fleet of vessels. The vessels have specific capacities and can be chartered under different agreements. The inventory levels of all consumption nodes and some production nodes should be maintained within specified bounds; for the remaining production nodes, orders should be picked up within pre-defined time windows. We propose a discrete-time mixed-integer programming model. In the face of new information and uncertainty, this optimization model has to be re-solved, as the horizon is rolled forward. We discuss how to account for different sources of uncertainty. We present a rolling-horizon reoptimization framework that allows us to study different policies that impact the quality of the implemented solution, so we can identify the optimal set of policies.     

E. H. Dirksens Beiträge zu den Grundlagen der Analysis

Enno Heeren Dirksen (1788–1850) was one of several mathematicians originating from Eastern Frisia at the end of the eighteenth century to acquire prominence in neohumanist reformed Prussia. While striving—like so many of his contemporaries—for more rigour in the foundations of calculus, his work is significant due to his unusual emphasis on the semiotic aspects of the basic concepts. As a clear-sighted propagator of Cauchy's conceptual innovations in Germany, his achievements in improving sign expressions of such concepts enabled him to clarify hitherto not differentiated multiple limit processes—although less successfully in constructive concept formation itself. The contribution is based on the analysis of Dirksen's published texts and on the numerous texts which remained drafts for his projected voluminousOrganon der gesamten Analysis.

---

---

Menso Folkerts zum 60. Geburtstag gewidmet     

DISPERSION COMPENSATION CFBG IN100km 10Gbit／s RECIRCULATING SYSTEMS

A 10Gbit/s recirculating system is configured with Chirped Fiber Bragg Grating (CFBG) for the dispersion compensation. For the first time, the transmission distance in the loop reaches 1000km with bit error rate of 10-9. The effect of the group delay ripple of the fiber grating is also investigated in the recirculating systems, and it is shown that the transmission distance is limited to 4 cycles (4×167.1km ) in the loop with the power penalty fluctuation below 1.0dB. Thus the group delay ripple should be reduced to allow for the wavelength drift of±5GHz. At the end of this letter, the principles are given for designing long haul recirculating systems with dispersion compensation CFBG.     

Synthesis and characterization of biocompatible hydroxyapatite coated ferrite

Ferrite particles coated with biocompatible phases can be used for hyperthermia treatment of cancer. We have synthesized substituted calcium hexaferrite, which is not stable on its own but is stabilized with small substitution of La. Hexaferrite of chemical composition (CaO)_0.75(La₂0₃)_0.20(Fe₂O₃)₆ was prepared using citrate gel method. Hydroxyapatite was prepared by precipitating it from aqueous solution of Ca(NO₃)₂ and (NH₄)₂HPO₄ maintaining pH above 11. Four different methods were used for coating of hydroxyapatite on ferrite particles. SEM with EDX and X-ray diffraction analysis shows clear evidence of coating of hydroxyapatite on ferrite particles. These coated ferrite particles exhibited coercive field up to 2 kOe, which could be made useful for hysteresis heating in hyperthermia. Studies by culturing BHK-21 cells and WBC over the samples show evidence of biocompatibility. SEM micrographs and cell counts give clear indication of cell growth on the surface of the sample. Finally coated ferrite particle was implanted in Kasaulli mouse to test its biocompatibility. The magnetic properties and biocompatibility studies show that these hydroxyapatite coated ferrites could be useful for hyperthermia.